When it comes to practicality and price, wearing a pair of clip on flip up sunglasses is the way to go because it is easier to use and cheaper than the actual kind. One of the best things about these things is that they are very simple to create right at home and that they do not cost much to make at all. Now just to give people an idea on how to make one, here are some steps that will make the process easier.
The first step would be to get hold of an old pair of sunglasses and use a small screwdriver to take the arms of the glasses out. When one does this, then all that will be left would be a pair of lenses of the sunglasses. Take note that the pair of glasses right now is very delicate and may break if not handled well.
The next thing to do would get an old paper clip that is rather hard and a pair of pliers. Now the thing that one should do with the paper clip would be to straighten it out using the pliers. Remember to straighten it out slowly and carefully because it is possible that the paper clip might break.
Once he has straightened it out, then the next thing he should do would be to cut the wire in half so that he has two pieces. Now he should take one of the wires and slot it into the place where the arms of the glasses used to be. He should also do the same thing with the other side.
After the wires have been slotted in, then the next thing that one should do would be to actually tie the wires to the holes. The thing about this is that it is very hard to tie the wires by hand because these things are really tough. So in order to make a tight knot, one should use pliers to be able to tie the wire so that it will not be loose later on.
From there, take the two ends and place them in the center top part of the glasses. Always remember to embed the wires to the frame to make sure that the wire will be invisible to the eyes of the public. Once this is done, tie the two ends together in order to make a small clip in the middle.
The last thing to do here would be to make a small curve in the middle part so that it can be attached to the glasses. If there is already a small bend, then one should try clipping it on the eyeglasses to check if it looks good. If it looks fine, then one may now go out and start wearing it.
So if one is interested in making this thing, try following these steps to making clip on flip up sunglasses. This is guaranteed to be better than buying a new pair because it is cheaper and easier to use. It will also not get broken easily like an actual pair of sunglasses.
The first step would be to get hold of an old pair of sunglasses and use a small screwdriver to take the arms of the glasses out. When one does this, then all that will be left would be a pair of lenses of the sunglasses. Take note that the pair of glasses right now is very delicate and may break if not handled well.
The next thing to do would get an old paper clip that is rather hard and a pair of pliers. Now the thing that one should do with the paper clip would be to straighten it out using the pliers. Remember to straighten it out slowly and carefully because it is possible that the paper clip might break.
Once he has straightened it out, then the next thing he should do would be to cut the wire in half so that he has two pieces. Now he should take one of the wires and slot it into the place where the arms of the glasses used to be. He should also do the same thing with the other side.
After the wires have been slotted in, then the next thing that one should do would be to actually tie the wires to the holes. The thing about this is that it is very hard to tie the wires by hand because these things are really tough. So in order to make a tight knot, one should use pliers to be able to tie the wire so that it will not be loose later on.
From there, take the two ends and place them in the center top part of the glasses. Always remember to embed the wires to the frame to make sure that the wire will be invisible to the eyes of the public. Once this is done, tie the two ends together in order to make a small clip in the middle.
The last thing to do here would be to make a small curve in the middle part so that it can be attached to the glasses. If there is already a small bend, then one should try clipping it on the eyeglasses to check if it looks good. If it looks fine, then one may now go out and start wearing it.
So if one is interested in making this thing, try following these steps to making clip on flip up sunglasses. This is guaranteed to be better than buying a new pair because it is cheaper and easier to use. It will also not get broken easily like an actual pair of sunglasses.
No comments:
Post a Comment